South Wales Steel Buildings

Steel building designer

Work through footprint, roof profile, finish, openings, dwarf wall and groundworks, with a live 3D view updating at every choice. Finish by requesting a quote: the complete specification and a materials take-off travel with it to South West Steel Buildings, who design, supply and erect every building.

Preparing the 3D designer…

Seven stages, start to finish

Begin with the building’s job, since that sets a suitable floor specification, then its footprint: up to 20 metres of span and 40 metres of length, with eaves anywhere from 2.1 to 6 metres. Bay spacing follows automatically and never exceeds six metres, which is how the portal frames are fabricated.

Next comes the roof profile, twin-slope apex or single mono-pitch, pitched anywhere from 5 to 30 degrees. After that, sheeting for sides and roof, each in any of 20 standard finishes, single skin or insulated composite. Openings follow: roller shutters, personnel doors and double doors, placed on whichever elevation you choose and positioned by slider or by dragging directly on the model. Doors keep clear of the corner columns and of one another, and can never be taller than the eaves permit.

The final two stages cover what frame quotations normally exclude: an optional dwarf wall of blockwork, brickwork or precast panels, then the concrete floor and earthworks beneath. Each stage validates your entries before you continue, so nothing impossible reaches the quote.

The specification you send

Your request carries every decision in plain words. Dimensions and bay layout; roof angle and ridge height; sheeting type and colour references for sides and roof; trim and gutter choices; each door’s size, elevation and offset from its corner; and the number of rooflight rows.

Alongside sits the groundworks take-off. Choose a blockwork or brickwork dwarf wall and it lists units to order, mortar, column ties, damp-proof course and footing concrete. For the floor it gives ready-mix volume, sub-base tonnage, reinforcement and spoil loads for haulage. You review all of it on the specification screen before anything is submitted.

Add a name, a phone number or email, and the site postcode, which lets delivery and erection be priced for your location anywhere from Newport to Pembrokeshire.

Deliberately outside its scope

Pricing stays with South West Steel Buildings, because an engineered frame cannot be costed fairly without engineering. Column pad footings are likewise excluded: their dimensions come from the structural calculations and a soil assessment, and estimating them here would only mislead.

Consent is separate as well. Agricultural buildings in Wales often proceed under prior notification to the local planning authority rather than a full application, while larger commercial units need planning permission and, alongside it, Building Regulations approval. The designer flags whether Building Regulations are likely to apply; your planning authority decides the rest.

Questions people ask

Will the designer tell me what the building costs?
No, and that is intentional. A steel frame is engineered for its site: exposure, snow load, span and door openings all change how much steel goes into it, and none of that can be judged fairly by a browser. South West Steel Buildings quote directly from the specification you build here, so what comes back is a figure for your building rather than a rough band for something like it.
How reliable are the groundworks numbers?
They are an estimate of quantities, not a price: concrete volumes, sub-base tonnage, reinforcement, spoil loads and, where you add a dwarf wall, the blockwork or brickwork with its mortar, ties and footing. They come from the same engine as the standalone groundworks calculator. A contractor or structural engineer should check them against your soil before ordering, and column pad footings are left for the frame design to size.
Does it remember my design?
For as long as the browser tab stays open. Reloading the page or visiting another part of the site keeps it; closing the tab clears it. None of your contact details are held anywhere until you press the button that requests your quote.
My building is larger than the designer allows. What now?
The designer runs to 20 metres wide and 40 metres long, matching the standard range. Larger or unusual structures are engineered one at a time; send a general enquiry with approximate dimensions and the conversation starts from there.
Can I trust the colours I see?
Only as a rough guide. The 20 standard finishes are listed by name and RAL or BS reference, but monitors and phones render them differently. Request a physical sample before committing, particularly where planning conditions specify a colour or the new building has to match an existing one.

Other buildings we cover

Same approach on each: what the building is, how it gets sized, where you stand on planning, and what the base underneath it comes to.

Prefer a conversation instead?

A rough footprint and the building’s purpose are enough for a first reply that moves things forward. Only need the base worked out? The groundworks calculator does just that.